Other causes of compressor oil separator failure
In the actual handling process, we have found that a considerable proportion of the fault complaints are not caused by the quality issues of the oil separator. So, apart from the quality issue of the oil separator, what other reasons can lead to oil leakage in the oil separator? In fact, these several situations can also lead to oil leakage:
1. Fault of the minimum pressure valve
The minimum pressure valve is a component that maintains the pressure of the screw compressor system. If there is a leakage point at the sealing part of the minimum pressure valve or if the minimum pressure valve opens in advance (as the design opening pressure varies among different manufacturers, usually ranging from 3.5 to 5.5bar), then the time it takes for the machine to establish the pressure in the oil and gas tank during the initial operation will increase At this time, the oil mist concentration of the gas in a low-pressure state is high. When passing through the oil separator, the flow rate is fast, the load on the oil separator increases, the separation effect decreases, and the oil consumption is large.
Solution: Inspect the minimum pressure valve and replace it if necessary.
Second, substandard compressor lubricating oil was used
At present, all commonly used screw compressors have high-temperature protection, and their typical tripping temperature is around 110 to 120 degrees Celsius. However, some compressors use substandard lubricating oil, and when the exhaust temperature is high, varying degrees of oil consumption will occur (based on this, the higher the temperature, the greater the oil consumption). The reason is that at high temperatures, after the primary separation in the oil and gas tank, some oil droplets can have the same order of magnitude as the gas phase molecules, with a molecular diameter of ≤0.01μm. The oil separator is unable to capture and separate them, resulting in excessive oil consumption.
Solution: Identify the cause of the high temperature, solve the problem to lower the temperature, and choose high-quality screw compressor lubricating oil as much as possible.
Third, the design of the oil and gas separation tank is not standardized
Some compressor manufacturers, when designing oil-gas separation tanks, have an unreasonable design of the primary separation system, resulting in an unsatisfactory primary separation effect. This leads to a very high oil mist concentration before entering the oil separator, an excessive load on the oil separator, insufficient processing capacity, and excessive oil consumption.
Solution: The manufacturer should improve the design to enhance the effect of primary separation.
Four. Excessive refueling
When the fuel level exceeds the normal level, some of the engine oil is carried away by the airflow, resulting in excessive fuel consumption.
Solution: After the machine stops, wait until the pressure in the oil and gas tank drops to zero, then open the oil drain valve and release the oil to the normal level.
V. The return oil check valve is damaged
If the return oil check valve is damaged (changing from one-way to two-way), after the machine stops, the pressure inside the oil separator tank will cause a large amount of engine oil to flow back into the oil separator through the return oil pipe. When the machine runs next time, the engine oil inside the oil separator will not be able to be sucked back to the machine head in time. This causes some of the engine oil to escape from the compressor along with the separated air (this situation is common in machines without an oil circuit stop valve and a check valve at the exhaust outlet of the compressor head).
Solution: After disassembling, check the check valve. If there is any debris blocking it, clear the debris. If the check valve is damaged, replace it with a new one.
Six. Improper installation of the return oil pipe
When replacing, cleaning or maintaining the compressor, if the return oil pipe is not inserted to the bottom of the oil separator (reference: It is better to be 1 to 2mm away from the arc center of the bottom of the oil separator), the separated oil cannot return to the compressor head in time, and the accumulated oil will escape along with the compressed air.
Solution: Shut down the machine. After the pressure is released to zero, adjust the return oil pipe to a reasonable height (the return oil pipe should be 1 to 2mm away from the bottom of the oil separator. For inclined return oil pipes, they can be inserted to the bottom of the oil separator).
Seven. Large gas consumption
Or it is used under overload and low pressure (or the oil separation treatment capacity selected before the machine leaves the factory is too tightly matched with the machine's exhaust volume)
Low-pressure load operation refers to the situation where, when users operate the compressor, the exhaust pressure does not reach the rated working pressure of the compressor itself, but it can basically meet the gas usage requirements of some enterprise users.
For instance, when an enterprise user adds gas-consuming equipment, the gas consumption increases, making it impossible for the compressor's exhaust volume to reach a balance with the user's gas consumption. Suppose the rated exhaust pressure of the compressor is 8bar, but in actual use, the pressure is only 5bar or even lower. As a result, the compressor remains in a state of load operation for a long time and cannot reach the rated pressure value of the machine, leading to an increase in fuel consumption. The reason is that, under the condition of constant exhaust volume, when the oil-gas mixture passes through the oil separator, the flow rate increases, the oil mist concentration is too high, which increases the load on the oil separator and ultimately leads to a large amount of fuel consumption.
Solution: It is recommended to contact the manufacturer and exchange for an oil separator product that can be used at low pressure.
Viii. Blockage of the return oil pipeline
When the return oil pipeline (including the check valve on the return oil pipeline and the return oil filter screen) is blocked by foreign objects, the oil that has been separated and condensed at the bottom of the oil separator cannot return to the engine head. The already condensed oil droplets are blown up by the airflow and carried away along with the separated air. These foreign objects are usually caused by solid impurities that fall during installation.
Solution: Shut down the machine. After the pressure in the oil drum is released to zero, remove all the pipe fittings of the return oil pipe and blow out the blocked foreign objects. When installing the built-in oil separator, make sure to clean the oil and gas tank cover thoroughly. At the same time, pay attention to whether there are any solid particles remaining at the bottom of the oil separator core.




